ENGAGE-WAN-MIB DEFINITIONS ::= BEGIN IMPORTS enterprises, IpAddress, Gauge, Counter FROM RFC1155-SMI -- Unsigned32 -- FROM SNMPv2-SMI OBJECT-TYPE FROM RFC-1212 ifIndex FROM RFC1213-MIB; -- textual conventions DisplayString ::= OCTET STRING -- This data type is used to model textual information taken -- from the NVT ASCII character set. By convention, objects -- with this syntax are declared as having -- -- SIZE (0..255) PhysAddress ::= OCTET STRING -- This data type is used to model media addresses. For many -- types of media, this will be in a binary representation. -- For example, an ethernet address would be represented as -- a string of 6 octets. engage OBJECT IDENTIFIER ::= { enterprises 1133 } engageWAN OBJECT IDENTIFIER ::= { engage 5 } -- Engage Common WAN Configuration Table engageWANIfConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF EngageWANIfConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains objects common to WAN interface configuration." ::= { engageWAN 1 } engageWANIfConfigEntry OBJECT-TYPE SYNTAX EngageWANIfConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing objects describing the configuration of a particular WAN interface." INDEX { ifIndex } ::= { engageWANIfConfigTable 1 } EngageWANIfConfigEntry ::= SEQUENCE { engageWANIfType INTEGER, engageWANDs1IfConfigLBO INTEGER, engageWANDs1E1IfConfigLineMode INTEGER, engageWANDs1E1IfConfigEqualization INTEGER, engageWANIfConfigClocking INTEGER, engageWANIfConfigClockingTuneValue INTEGER, engageWANIfConfigClockingTPLLRail INTEGER, engageWANDs1E1IfConfigData INTEGER, engageWANDs1E1IfConfigFraming INTEGER, engageWANDs1E1IfConfigCoding INTEGER, engageWANIfProtocol INTEGER, engageWANDs1E1IfConfigTxUnderrunAIS INTEGER, engageWANDs1E1IfConfigDS0Bitmap Gauge, engageWANDs1E1IfConfigIdleChar INTEGER } engageWANIfType OBJECT-TYPE SYNTAX INTEGER { ds1(1), e1(2), rs530(3), v35(4), other(5), e3(6), t3(7) } ACCESS read-write STATUS mandatory DESCRIPTION "This object specifies this interface's physical type. A set of this object will initiate a change of the type when a configuration save happens." ::= { engageWANIfConfigEntry 1 } engageWANDs1IfConfigLBO OBJECT-TYPE SYNTAX INTEGER { csuNeg15dB(1), csuNeg22point5dB(2), csuNeg7point5dB(3), csuNeg0dB(4), dsx0To133Ft(5), dsx133To266Ft(6), dsx266To399(7), dsx399To533(8), dsx533To655(9) } ACCESS read-write STATUS optional DESCRIPTION "This object applies to DS1 interfaces only. This specifies the line build out for this particular DS1 interface. A set of this object will initiate a change of the line build out when a configuration save happens." ::= { engageWANIfConfigEntry 2 } engageWANDs1E1IfConfigLineMode OBJECT-TYPE SYNTAX INTEGER { terminate(1), monitor(2) } ACCESS read-write STATUS optional DESCRIPTION "This object is only applicable to T1 or E1. It specifies the physical mode of this interface, whether it is terminating or monitoring. A set of this object will initiate a change of the line mode when a configuration save happens." ::= { engageWANIfConfigEntry 3 } engageWANDs1E1IfConfigEqualization OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS optional DESCRIPTION "This object is only applicable to T1 or E1. It specifies whether or not T1/E1 equalization is enabled on this interface. A set of this object will initiate a change of the line mode when a configuration save happens." ::= { engageWANIfConfigEntry 4 } engageWANIfConfigClocking OBJECT-TYPE SYNTAX INTEGER { network(1), -- derived from remote end internal(2), -- local pll(3), engageReserved(4), tuned(5), v2pll(6), tpll(7) } ACCESS read-write STATUS mandatory DESCRIPTION "This object specifies the clock mode of this interface. A set of this object will initiate a change of the clock mode when a configuration save happens." ::= { engageWANIfConfigEntry 5 } engageWANIfConfigClockingTuneValue OBJECT-TYPE SYNTAX INTEGER (1..255) ACCESS read-write STATUS mandatory DESCRIPTION "This object specifies the value for tuning the clock frequency if engageWANIfConfigClocking is is set to tuned. This object also specifies the clocking center frequency if engageWANIfConfigClocking is set to tpll. A set of this object will initiate a change of the clock frequency when a configuration save happens." ::= { engageWANIfConfigEntry 6 } engageWANIfConfigClockingTPLLRail OBJECT-TYPE SYNTAX INTEGER (1..255) ACCESS read-write STATUS mandatory DESCRIPTION "This object specifies the value for tuning the maximum swing away from the center frequency allowed if engageWANIfConfigClocking is set to tpll. A set of this object will initiate a change of the threshold when a configuration save happens." ::= { engageWANIfConfigEntry 7 } engageWANDs1E1IfConfigData OBJECT-TYPE SYNTAX INTEGER { normal(1), inverted(2) } ACCESS read-write STATUS optional DESCRIPTION "This object specifies the signal mode of this DS1 or E1 interface's data. A set of this object will initiate a change of the data mode when a a configuration save happens." ::= { engageWANIfConfigEntry 8 } engageWANDs1E1IfConfigFraming OBJECT-TYPE SYNTAX INTEGER { esf(1), d4(2), fas(3), crc4(4), unframed(5) } ACCESS read-write STATUS optional DESCRIPTION "This object specifies the framing type of this DS1 or E1 interface. A set of this object will initiate a change of the framing type when a configuration save happens." ::= { engageWANIfConfigEntry 9 } engageWANDs1E1IfConfigCoding OBJECT-TYPE SYNTAX INTEGER { ami(1), b8zs(2), hdb3(3), other(4) } ACCESS read-write STATUS optional DESCRIPTION "This object specifies the coding type of this DS1 or E1 interface. A set of this object will initiate a change of the coding type when a configuration save happens." ::= { engageWANIfConfigEntry 10 } engageWANIfProtocol OBJECT-TYPE SYNTAX INTEGER { other(1), ipTube(2), cesoIP(3), hdlcoIP(4), adp(5), ethernetCsmacd(6), engage(7), ppp(8), frameRelay(9) } ACCESS read-write STATUS mandatory DESCRIPTION "This object specifies the link layer protocol that services the traffic flow through this interface. Setting this object will initiate a change to the protocol that will take effect during a saving of the configuration." ::= { engageWANIfConfigEntry 11 } engageWANDs1E1IfConfigTxUnderrunAIS OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS optional DESCRIPTION "This object specifies whether or not an AIS is generated if the T1 or E1 transmitter underruns. A set of this object will initiate a change of this setting when a configuration save happens." ::= { engageWANIfConfigEntry 12 } engageWANDs1E1IfConfigDS0Bitmap OBJECT-TYPE SYNTAX Gauge ACCESS read-write STATUS optional DESCRIPTION "This object specifies the DS0 utilization of this DS1 or E1 line. The value is a bitmap in which the most significant bit represents the first DS0, the second most significant bit represents the second DS0, and etc. A set of this object will initiate a change of the DS0 utilization when a configuration save happens." ::= { engageWANIfConfigEntry 13 } engageWANDs1E1IfConfigIdleChar OBJECT-TYPE SYNTAX INTEGER (1..256) ACCESS read-write STATUS optional DESCRIPTION "This object specifies the idle character for this DS1 or E1 interface. This is typically 0x7E (hexadecimal). A set of this object will initiate a change of the idle character when a configuration save happens. To set the idle character to zero, this object must be set with the value 256." ::= { engageWANIfConfigEntry 14 } engageWANIfIPTube OBJECT IDENTIFIER ::= { engageWAN 2 } engageWANIfIPTubeConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF EngageWANIfIPTubeConfigEntry ACCESS not-accessible STATUS optional DESCRIPTION "A list of IP Tube Configuration item entries." ::= { engageWANIfIPTube 1 } engageWANIfIPTubeConfigEntry OBJECT-TYPE SYNTAX EngageWANIfIPTubeConfigEntry ACCESS not-accessible STATUS optional DESCRIPTION "An entry containing objects describing the current configuration of an IP Tube for a particular interface." INDEX { ifIndex } ::= { engageWANIfIPTubeConfigTable 1 } EngageWANIfIPTubeConfigEntry ::= SEQUENCE { engageWANIfIPTubeConfigScrClockMode INTEGER, engageWANIfIPTubeConfigScrClockFactor INTEGER, engageWANIfIPTubeConfigSctClockMode INTEGER, engageWANIfIPTubeConfigSctClockFactor INTEGER, engageWANIfIPTubeConfigPacketInterval INTEGER, engageWANIfIPTubeConfigPercentBytesPerFrame INTEGER, engageWANIfIPTubeConfigFraming INTEGER, engageWANIfIPTubeConfigBuffers INTEGER, engageWANIfIPTubeConfigOverflowLimit INTEGER, engageWANIfIPTubeConfigFPP INTEGER, engageWANIfIPTubeConfigCompression INTEGER, engageWANIfIPTubeConfigCompressionSilenceDetect INTEGER, engageWANIfIPTubeConfigCompressionSilenceDetectThreshold INTEGER, engageWANIfIPTubeConfigCompressionSilenceDetectChannels Gauge, engageWANIfIPTubeConfigTestMode INTEGER, engageWANIfIPTubeConfigNumDuplicates INTEGER, engageWANIfIPTubeConfigLANPort INTEGER, engageWANIfIPTubeConfigEthernet802dot1pState INTEGER, engageWANIfIPTubeConfigEthernet802dot1pPriority INTEGER, engageWANIfIPTubeConfigLAN1ARP INTEGER, engageWANIfIPTubeConfigLAN1DestEthernetAddr PhysAddress, engageWANIfIPTubeConfigLAN1DynamicAddressingState INTEGER, engageWANIfIPTubeConfigLAN1DestIPAddr IpAddress, engageWANIfIPTubeConfigLAN1DestDomainName DisplayString, engageWANIfIPTubeConfigLAN1TOS INTEGER, engageWANIfIPTubeConfigLAN1DestUDPPort INTEGER, engageWANIfIPTubeConfigLAN2ARP INTEGER, engageWANIfIPTubeConfigLAN2DestEthernetAddr PhysAddress, engageWANIfIPTubeConfigLAN2DynamicAddressingState INTEGER, engageWANIfIPTubeConfigLAN2DestIPAddr IpAddress, engageWANIfIPTubeConfigLAN2DestDomainName DisplayString, engageWANIfIPTubeConfigLAN2TOS INTEGER, engageWANIfIPTubeConfigLAN2DestUDPPort INTEGER, engageWANIfIPTubeConfigIfDescr DisplayString, engageWANIfIPTubeConfigSuperTube INTEGER } engageWANIfIPTubeConfigScrClockMode OBJECT-TYPE SYNTAX INTEGER { nx64k(1), nx56k(2), nx2k4(3), nx4m(4), nx5m(5), nx8m(6) } ACCESS read-write STATUS optional DESCRIPTION "This object is applicable to the IP Tube RS-530 only and determines the base frequency for the serial receive line rate. This value multiplied by the engageWANIfIPTubeConfigScrClockFactor value gives the serial receive clock frequency of this interface. A set of this object will initiate a change of the receive clock frequency when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 1 } engageWANIfIPTubeConfigScrClockFactor OBJECT-TYPE SYNTAX INTEGER (1..32) ACCESS read-write STATUS optional DESCRIPTION "This object is applicable to the IP Tube RS-530 only and determines the factor for the serial receive line rate. This value multiplied by the engageWANIfIPTubeConfigScrClockMode value gives the serial frequency of this interface. A set of this object will initiate a change of the receive clock when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 2 } engageWANIfIPTubeConfigSctClockMode OBJECT-TYPE SYNTAX INTEGER { nx64k(1), nx56k(2), nx2k4(3), nx4m(4), nx5m(5), nx8m(6) } ACCESS read-write STATUS optional DESCRIPTION "This object is applicable to the IP Tube RS-530 only and determines the base frequency for the serial transmit line rate. This value multiplied by the engageWANIfIPTubeConfigSctClockFactor value gives the serial transmit clock frequency of this interface. A set of this object will initiate a change of the transmit clock frequency when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 3 } engageWANIfIPTubeConfigSctClockFactor OBJECT-TYPE SYNTAX INTEGER (1..32) ACCESS read-write STATUS optional DESCRIPTION "This object is applicable to the IP Tube RS-530 only and determines the factor for the serial transmit line rate. This value multiplied by the engageWANIfIPTubeConfigSctClockMode value gives the serial transmit clock frequency of this interface. A set of this object will initiate a change of the transmit clock frequency when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 4 } engageWANIfIPTubeConfigPacketInterval OBJECT-TYPE SYNTAX INTEGER (1..32) ACCESS read-write STATUS optional DESCRIPTION "This object is applicable to the IP Tube RS-530 only. It determines the intervals between IP Tube packets. The effective data rate is the serial receive clock frequency divided by this value + 1. A set of this object will initiate a change of the interval when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 5 } engageWANIfIPTubeConfigPercentBytesPerFrame OBJECT-TYPE SYNTAX INTEGER (1..100) ACCESS read-write STATUS optional DESCRIPTION "This object is applicable to the IP Tube RS-530 only. It determines the percentage of clock pulses applied to this DCE interface. Possible settings are 100, 87, 75, 50, and 25. Any other settings will be rounded to the nearest of these values. A set of this object will initiate a change of the percentage when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 6 } engageWANIfIPTubeConfigFraming OBJECT-TYPE SYNTAX INTEGER { transparent(1), t1framed(2), e1framed(3), t1MultiFrame(4) } ACCESS read-write STATUS optional DESCRIPTION "This object is applicable to the IP Tube T1 and IP Tube E1. It specifies whether or not the E1 or T1 framing bit(s) are to be encapsulated into the IP Tube packet. The transparent setting will drop the T1 framing bit in T1 or the E1 framing byte in E1. A set of this object will initiate a change of the framing when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 7 } engageWANIfIPTubeConfigBuffers OBJECT-TYPE SYNTAX INTEGER (3..85) ACCESS read-write STATUS optional DESCRIPTION "This object applies to the IP Tube, CESOIP, and ADP protocols. It specifies the number of buffers of delay that the serial transmitter maintains to prevent underruns. A set of this object will initiate a change of the buffers value when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 8 } engageWANIfIPTubeConfigOverflowLimit OBJECT-TYPE SYNTAX INTEGER (3..85) ACCESS read-write STATUS optional DESCRIPTION "This object applies to the IP Tube, CESOIP, and ADP protocols. It specifies the number of packets greater than engageWANIfIPTubeConfigBuffers that the serial transmitter may accumulate before packets are dropped due to transmitter overrun. A set of this object will initiate a change of the threshold buffers value when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 9 } engageWANIfIPTubeConfigFPP OBJECT-TYPE SYNTAX INTEGER (1..56) ACCESS read-write STATUS optional DESCRIPTION "This object applies to the IP Tube, CESOIP, and ADP protocols. It specifies the number of frames encapsulated in an IP Tube Packet. For T1, this number ranges from 8 to 56, for E1 this number ranges from 8 to 40, and for RS-530 this number ranges from 1 to 16. A set of this object will initiate a change of the FPP when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 10 } engageWANIfIPTubeConfigCompression OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS optional DESCRIPTION "This object is applicable to the IP Tube T1 and IP Tube E1. It specifies whether or not IP Tube compression is enabled. A set of this object will initiate a change of the compression state when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 11 } engageWANIfIPTubeConfigCompressionSilenceDetect OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS optional DESCRIPTION "This object is applicable to the IP Tube T1 and IP Tube E1. It specifies whether or not IP Tube compression silence detection is enabled. A set of this object will initiate a change of the silence detection state when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 12 } engageWANIfIPTubeConfigCompressionSilenceDetectThreshold OBJECT-TYPE SYNTAX INTEGER (2..6) ACCESS read-write STATUS optional DESCRIPTION "This object is applicable to the IP Tube T1 and IP Tube E1. When compression silence detection is enabled, this specifies a threshold of background noise tolerated before the silence detection determines that a voice channel isn't silent; a 2 is the lowest threshold and 6 is the highest. A set of this object will initiate a change of the threshold when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 13 } engageWANIfIPTubeConfigCompressionSilenceDetectChannels OBJECT-TYPE SYNTAX Gauge ACCESS read-write STATUS optional DESCRIPTION "This object is applicable to the IP Tube T1 and IP Tube E1. When compression silence detection is enabled, this is a bitmap which specifies the DS0s on which silence detection is active; which the most significant bit represents the first DS0, the second most significant bit represents the second DS0, and etc. A set of this object will initiate a change of the silence detection state when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 14 } engageWANIfIPTubeConfigTestMode OBJECT-TYPE SYNTAX INTEGER { localLoop(1), remoteLoop(2) } ACCESS read-write STATUS optional DESCRIPTION "This object specifies the test mode of this interface when the corresponding ifAdminStatus is set to testing. localLoop means that the received data is transmitted back out. remoteLoop means that the data to be transmitted is looped back towards the interface. A set of this object will initiate a change of the loopback when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 15 } engageWANIfIPTubeConfigNumDuplicates OBJECT-TYPE SYNTAX INTEGER (1..256) ACCESS read-write STATUS optional DESCRIPTION "This object applies to the IP Tube, CESOIP, and HDLCOIP protocols. It specifies the number of duplicate packets sent after each IP Tube packet. To specify no duplicates, this object must be set to 256. A set of this object will initiate a change of the duplicate packets when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 16 } engageWANIfIPTubeConfigLANPort OBJECT-TYPE SYNTAX INTEGER { lan1(1), lan2(2), other(3), alternator(4), protector(5), altProtector(6) } ACCESS read-write STATUS optional DESCRIPTION "This object specifies which LAN port(s) the IP Tube packets will be forwarded through. The Alternator does an alternating transmission sequence over both LAN ports, the Protector sends IP Tube packets over the LAN1 as a primary link and uses LAN2 as a failover link, and the AltProtector uses the Alternator transmission path as the primary and uses either LAN port for a failover path. A set of this object will initiate a change of the tranmission path when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 17 } engageWANIfIPTubeConfigEthernet802dot1pState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS optional DESCRIPTION "This object specifies whether or not IP Tube packets have a specific 802.1P priority value in their tag. A set of this object will initiate a change of the tagging when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 18 } engageWANIfIPTubeConfigEthernet802dot1pPriority OBJECT-TYPE SYNTAX INTEGER (1..7) ACCESS read-write STATUS optional DESCRIPTION "This object specifies the 802.1P priority value if engageWANIfIPTubeConfigEthernet802dot1pState is enabled. A set of this object will initiate a change of the priority when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 19 } engageWANIfIPTubeConfigLAN1ARP OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS optional DESCRIPTION "This object determines whether this IP Tube will attempt to resolve the destination IP Tube address of this interface's data via ARP over the LAN1 interface. Disabling of this feature is necessary if engageLANIPTubeIfConfigBroadcastRcvEnabled is disabled for LAN1. A set of this object will initiate a change of the ARP state when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 20 } engageWANIfIPTubeConfigLAN1DestEthernetAddr OBJECT-TYPE SYNTAX PhysAddress ACCESS read-write STATUS optional DESCRIPTION "This object specifies the MAC address to which the data on this interface will be destined for if engageWANIfIPTubeConfigLAN1ARP is disabled. This is used when engageLANIPTubeIfConfigBroadcastRcvEnabled for LAN1 is disabled and IP Tube will not send broadcast ARP packets through LAN1. A set of this object will initiate a change of this MAC address setting when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 21 } engageWANIfIPTubeConfigLAN1DynamicAddressingState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS optional DESCRIPTION "This object enables or disables automatic detection via LAN1 of the remote IP Tube's IP address. A set of this object will initiate a change of the dynamic addressing state when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 22 } engageWANIfIPTubeConfigLAN1DestIPAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS optional DESCRIPTION "This object specifies the LAN1 destination IP Address for the data received from this IP Tube's serial interface. A set of this object will initiate a change of this setting when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 23 } engageWANIfIPTubeConfigLAN1DestDomainName OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS optional DESCRIPTION "This object specifies the fully qualified domain name of the LAN1 destination remote IPTUBE. In order to not use domain name qualification to send this interface's IP Tube traffic through LAN1, this object must be set to two consecutive double quotes. A set of this object will initiate a change of the domain name when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 24 } engageWANIfIPTubeConfigLAN1TOS OBJECT-TYPE SYNTAX INTEGER (1..256) ACCESS read-write STATUS optional DESCRIPTION "This object specifies the value of the TOS byte in the IP Tube's LAN1 packet encapsulation header for all data received on this serial interface. To specify a TOS of 0, this object must be set to 256. A set of this object will initiate a change of the TOS value when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 25 } engageWANIfIPTubeConfigLAN1DestUDPPort OBJECT-TYPE SYNTAX INTEGER (1..65536) ACCESS read-write STATUS optional DESCRIPTION "This object specifies the destination UDP port number of the IP Tube's LAN1 packet encapsulation header for all data received on this serial interface. To set a UDP port number of 0, this object must be set to 65536. A set of this object will initiate a change of the UDP port number when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 26 } engageWANIfIPTubeConfigLAN2ARP OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS optional DESCRIPTION "This object determines whether this IP Tube will attempt to resolve the destination IP Tube address of this interface's data via ARP over the LAN2 interface. Disabling of this feature is necessary if engageLANIPTubeIfConfigBroadcastRcvEnabled is disabled for LAN2. A set of this object will initiate a change of the ARP state when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 27 } engageWANIfIPTubeConfigLAN2DestEthernetAddr OBJECT-TYPE SYNTAX PhysAddress ACCESS read-write STATUS optional DESCRIPTION "This object specifies the MAC address to which the data on this interface will be destined for if engageWANIfIPTubeConfigLAN2ARP is disabled. This is used when engageLANIPTubeIfConfigBroadcastRcvEnabled for LAN2 is disabled and IP Tube will not send broadcast ARP packets through LAN2. A set of this object will initiate a change of this MAC address setting when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 28 } engageWANIfIPTubeConfigLAN2DynamicAddressingState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS optional DESCRIPTION "This object enables or disables automatic detection via LAN2 of the remote IP Tube's IP address. A set of this object will initiate a change of the dynamic addressing state when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 29 } engageWANIfIPTubeConfigLAN2DestIPAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS optional DESCRIPTION "This object specifies the LAN2 destination IP Address for the data received from this IP Tube's serial interface. A set of this object will initiate a change of this setting when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 30 } engageWANIfIPTubeConfigLAN2DestDomainName OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS optional DESCRIPTION "This object specifies the fully qualified domain name of the LAN2 destination remote IPTUBE. In order to not use domain name qualification to send this interface's IP Tube traffic through LAN2, this object must be set to a two consecutive double quotes. A set of this object will initiate a change of the domain name when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 31 } engageWANIfIPTubeConfigLAN2TOS OBJECT-TYPE SYNTAX INTEGER (1..256) ACCESS read-write STATUS optional DESCRIPTION "This object specifies the value of the TOS byte in the IP Tube's LAN2 packet encapsulation header for all data received on this serial interface. A set of this object will initiate a change of the TOS value when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 32 } engageWANIfIPTubeConfigLAN2DestUDPPort OBJECT-TYPE SYNTAX INTEGER (1..65536) ACCESS read-write STATUS optional DESCRIPTION "This object specifies the destination UDP port number of the IP Tube's LAN1 packet encapsulation header for all data received on this serial interface. A set of this object will initiate a change of the UDP port number when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 33 } engageWANIfIPTubeConfigIfDescr OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS optional DESCRIPTION "This object specifies the string describing this serial interface. This string is also reported for ifDescr. A set of this object will initiate a change of the string when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 34 } engageWANIfIPTubeConfigSuperTube OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS optional DESCRIPTION "This object specifies whether or not the SuperTube function is enabled. This object is only settable for the instance of first T1/E1 interface. A set of object will initiate a change of the SuperTube administrative status when a configuration save happens." ::= { engageWANIfIPTubeConfigEntry 35 } -- The IP Tube Protector Configuration Table engageWANIfIPTubeProtectorConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF EngageWANIfIPTubeProtectorConfigEntry ACCESS not-accessible STATUS optional DESCRIPTION "A list of IP Tube LAN Protector Configuration item entries." ::= { engageWANIfIPTube 2 } engageWANIfIPTubeProtectorConfigEntry OBJECT-TYPE SYNTAX EngageWANIfIPTubeProtectorConfigEntry ACCESS not-accessible STATUS optional DESCRIPTION "An entry containing the LAN Protector related configuration items of this interface." INDEX { ifIndex } ::= { engageWANIfIPTubeProtectorConfigTable 1 } EngageWANIfIPTubeProtectorConfigEntry ::= SEQUENCE { engageWANIfIPTubeProtectorConfigHardswitch INTEGER, engageWANIfIPTubeProtectorConfigPollingPeriod INTEGER, engageWANIfIPTubeProtectorConfigRxPacketPercent INTEGER, engageWANIfIPTubeProtectorConfigRxPacketsOutOfSequence INTEGER, engageWANIfIPTubeProtectorConfigTxUnderruns INTEGER, engageWANIfIPTubeProtectorConfigTxDrainDrops INTEGER, engageWANIfIPTubeProtectorConfigQualification INTEGER, engageWANIfIPTubeProtectorConfigChannels Gauge } engageWANIfIPTubeProtectorConfigHardswitch OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS optional DESCRIPTION "This object controls whether or not the Tube Protector disables IP Tube transmission over the LAN2 port for this serial interface. If Hardswitch is turned off, this means that on a switchover to LAN1 IP Tube transmission is still done over the LAN2 interface. Note: If LAN2 transmits traffic over a Bill On Demand circuit, then enabling Tube Protector Hardswitch is highly recommended in order to avoid exorbitant usage costs. A set of this object will initiate a change of the Hardswitch state when a configuration save happens." ::= { engageWANIfIPTubeProtectorConfigEntry 1 } engageWANIfIPTubeProtectorConfigPollingPeriod OBJECT-TYPE SYNTAX INTEGER (1..60) ACCESS read-write STATUS optional DESCRIPTION "This object controls the length of the Protector's polling period in seconds. The range of values is from 1 to 60. A set of this object will initiate a change of the polling period when a configuration save happens." ::= { engageWANIfIPTubeProtectorConfigEntry 2 } engageWANIfIPTubeProtectorConfigRxPacketPercent OBJECT-TYPE SYNTAX INTEGER (50..100) ACCESS read-write STATUS optional DESCRIPTION "This object controls the minimum percentage of expected IP Tube packets on LAN1 for this serial interface for which the Protector may deem that LAN1 is still good. If less than this percentage is received in a 15 second period on LAN1, the Protector switches IP Tube transmission to LAN2. The range is from 50 to 100. A set of this object will initiate a change of the percentage when a configuration save happens." ::= { engageWANIfIPTubeProtectorConfigEntry 3 } engageWANIfIPTubeProtectorConfigRxPacketsOutOfSequence OBJECT-TYPE SYNTAX INTEGER (5..200) ACCESS read-write STATUS optional DESCRIPTION "This object controls the number of IP Tube Received Out of Sequence packets permitted on LAN1 for this serial interface within a 15 second period before the Protector deems it necessary to switch to LAN2. The range is from 5 to 200. A set of this object will initiate a change of the threshold when a configuration save happens." ::= { engageWANIfIPTubeProtectorConfigEntry 4 } engageWANIfIPTubeProtectorConfigTxUnderruns OBJECT-TYPE SYNTAX INTEGER (5..200) ACCESS read-write STATUS optional DESCRIPTION "This object controls the number of Transmit Underruns permitted for this serial interface within a 15 second period before the Protector deems it necessary to switch IP Tube transmission to LAN2. The range is from 5 to 200. A set of this object will initiate of this object will initiate a change of the threshold when a configuration save happens." ::= { engageWANIfIPTubeProtectorConfigEntry 5 } engageWANIfIPTubeProtectorConfigTxDrainDrops OBJECT-TYPE SYNTAX INTEGER (5..200) ACCESS read-write STATUS optional DESCRIPTION "This object controls the number of Transmit Drain Drops for this serial interface permitted within a 15 second period before the Protector deems it necessary to switch IP Tube transmission to LAN2. The range is from 5 to 200. A set of this object will initiate a change of the threshold when a configuration save happens." ::= { engageWANIfIPTubeProtectorConfigEntry 6 } engageWANIfIPTubeProtectorConfigQualification OBJECT-TYPE SYNTAX INTEGER (1..10) ACCESS read-write STATUS optional DESCRIPTION "This object controls the length of time in minutes that LAN1 statistics need to be satisfactory in order for the Protector to switch this serial interface's IP Tube packet transmission to it. The range of values is from 1 to 10. A set of this object will initiate a change of the qualification when a configuration save happens." ::= { engageWANIfIPTubeProtectorConfigEntry 7 } engageWANIfIPTubeProtectorConfigChannels OBJECT-TYPE SYNTAX Gauge ACCESS read-write STATUS optional DESCRIPTION "This object is only applicable to the AltProtector and designates the DS0s transmitted and received during failover of the AltProtector, This is a bitmap which specifies the DS0s on which silence detection is active; which the most significant bit represents the first DS0, the second most significant bit represents the second DS0, and etc. A set of this object will initiate a change of the DS0 utilization when a configuration save happens." ::= { engageWANIfIPTubeProtectorConfigEntry 8 } -- The IP Tube ADP Configuration Table engageWANIfIPTubeADPConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF EngageWANIfIPTubeADPConfigEntry ACCESS not-accessible STATUS optional DESCRIPTION "A list of IP Tube ADP Configuration item entries." ::= { engageWANIfIPTube 3 } engageWANIfIPTubeADPConfigEntry OBJECT-TYPE SYNTAX EngageWANIfIPTubeADPConfigEntry ACCESS not-accessible STATUS optional DESCRIPTION "An entry containing the ADP related configuration items of this interface." INDEX { ifIndex } ::= { engageWANIfIPTubeADPConfigTable 1 } EngageWANIfIPTubeADPConfigEntry ::= SEQUENCE { engageWANIfIPTubeADPConfigDelayRetransmit INTEGER, engageWANIfIPTubeADPConfigLimitRetransmit INTEGER, engageWANIfIPTubeADPConfigCountRetransmit INTEGER } engageWANIfIPTubeADPConfigDelayRetransmit OBJECT-TYPE SYNTAX INTEGER (2..85) ACCESS read-write STATUS optional DESCRIPTION "This object specifies the delay before the ADPIPTUBE protocol retransmits an unacknowledged packet. The delay is expressed in terms of Tube packets. A set of this object will initiate a change of the threshold when a configuration save happens." ::= { engageWANIfIPTubeADPConfigEntry 1 } engageWANIfIPTubeADPConfigLimitRetransmit OBJECT-TYPE SYNTAX INTEGER (2..85) ACCESS read-write STATUS optional DESCRIPTION "This object specifies the maximum number of unacknowledged packets the ADPIPTUBE protocol will retransmit after transmitting a tube packet. This parameter may not be greater than the corresponding engageWANIfIPTubeConfigBuffers. A set of this object will initiate a change of the threshold when a configuration save happens." ::= { engageWANIfIPTubeADPConfigEntry 2 } engageWANIfIPTubeADPConfigCountRetransmit OBJECT-TYPE SYNTAX INTEGER (2..85) ACCESS read-write STATUS optional DESCRIPTION "This object specifies the minimum interval, expressed in terms of Tube packets, before a retransmitted packet is retransmitted again. This parameter may not be greater than the corresponding engageWANIfIPTubeConfigBuffers. A set of this object will initiate a change of this setting when a configuration save happens." ::= { engageWANIfIPTubeADPConfigEntry 3 } engageWANIfIPTubeStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF EngageWANIfIPTubeStatsEntry ACCESS not-accessible STATUS optional DESCRIPTION "This is a table of the IP Tube specific statistics for this interface." ::= { engageWANIfIPTube 4 } engageWANIfIPTubeStatsEntry OBJECT-TYPE SYNTAX EngageWANIfIPTubeStatsEntry ACCESS not-accessible STATUS optional DESCRIPTION "This is an entry containing the IP Tube specific statistics for this interface." INDEX { ifIndex } ::= { engageWANIfIPTubeStatsTable 1 } EngageWANIfIPTubeStatsEntry ::= SEQUENCE { engageWANIfIPTubeStatsRxOutOfSequence Counter, engageWANIfIPTubeStatsRxArrivingTooLate Counter, engageWANIfIPTubeStatsRxNotArriving Counter, engageWANIfIPTubeStatsRxBadSourceIPAddr Counter, engageWANIfIPTubeStatsRxBadUDPPort Counter, engageWANIfIPTubeStatsTxDrainDrops Counter } engageWANIfIPTubeStatsRxOutOfSequence OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "This counter indicates the number of IP Tube packets received out of sequence from the LAN for the Tube stream of this interface." ::= { engageWANIfIPTubeStatsEntry 1 } engageWANIfIPTubeStatsRxArrivingTooLate OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "This counter indicates the number of IP Tube packets received too late for T1/E1 transmission from the LAN for the Tube stream of this interface." ::= { engageWANIfIPTubeStatsEntry 2 } engageWANIfIPTubeStatsRxNotArriving OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "This counter indicates the number of IP Tube packets not received when expected from the LAN for the Tube stream of this interface." ::= { engageWANIfIPTubeStatsEntry 3 } engageWANIfIPTubeStatsRxBadSourceIPAddr OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "This counter indicates the number of IP Tube packets received from the LAN that did not have the correct source IP address but the correct UDP port number for the Tube stream of this interface." ::= { engageWANIfIPTubeStatsEntry 4 } engageWANIfIPTubeStatsRxBadUDPPort OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "This counter indicates the number of IP Tube packets received from the LAN that did not have the correct UDP port number but the correct IP address for the Tube stream of this interface." ::= { engageWANIfIPTubeStatsEntry 5 } engageWANIfIPTubeStatsTxDrainDrops OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "This counter indicates the number of IP Tube packets from the LAN that were dropped due to overrun of the Tube Buffers threshold." ::= { engageWANIfIPTubeStatsEntry 6 } engageWANDS3E3 OBJECT IDENTIFIER ::= { engageWAN 3 } -- Engage Common DS3/E3 Statistics Table engageWANCommonDs3E3StatusTable OBJECT-TYPE SYNTAX SEQUENCE OF EngageWANCommonDs3E3StatusEntry ACCESS not-accessible STATUS optional DESCRIPTION "This is a table of common status items for DS3/E3 interfaces." ::= { engageWANDS3E3 1 } engageWANCommonDs3E3StatusEntry OBJECT-TYPE SYNTAX EngageWANCommonDs3E3StatusEntry ACCESS not-accessible STATUS optional DESCRIPTION "An entry containing the status of a particular DS3 or E3 interface." INDEX { ifIndex } ::= { engageWANCommonDs3E3StatusTable 1 } EngageWANCommonDs3E3StatusEntry ::= SEQUENCE { engageWANCommonDs3E3TubeEnetRxAbsent INTEGER } engageWANCommonDs3E3TubeEnetRxAbsent OBJECT-TYPE SYNTAX INTEGER { normal(1), rxAbsent(2) } ACCESS read-only STATUS optional DESCRIPTION "This object gives the current status of IP Tube packet reception for this DS3 or E3 interface." ::= { engageWANCommonDs3E3StatusEntry 1 } engageWANCommonDs3E3StatsTable OBJECT-TYPE SYNTAX SEQUENCE OF EngageWANCommonDs3E3StatsEntry ACCESS not-accessible STATUS optional DESCRIPTION "This is a table of common statistics for DS3/E3 interfaces." ::= { engageWANDS3E3 2 } engageWANCommonDs3E3StatsEntry OBJECT-TYPE SYNTAX EngageWANCommonDs3E3StatsEntry ACCESS not-accessible STATUS optional DESCRIPTION "An entry containing the statistics of a particular DS3 or E3 interface." INDEX { ifIndex } ::= { engageWANCommonDs3E3StatsTable 1 } EngageWANCommonDs3E3StatsEntry ::= SEQUENCE { engageWANCommonDs3E3StatsTxUnErrors Counter, engageWANCommonDs3E3StatsTxMiscErrors Counter, engageWANCommonDs3E3StatsTxQueueDepth Gauge, engageWANCommonDs3E3StatsRxCrcErrors Counter, engageWANCommonDs3E3StatsRxOvErrors Counter, engageWANCommonDs3E3StatsRxFramingErrors Counter, engageWANCommonDs3E3StatsRxMiscErrors Counter, engageWANCommonDs3E3StatsRxQueueDepth Gauge } engageWANCommonDs3E3StatsTxUnErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "This counter shows the number of Transmit Underruns on a particular DS3 or E3 interface. This value may be cleared via the Engage User Interface." ::= { engageWANCommonDs3E3StatsEntry 1 } engageWANCommonDs3E3StatsTxMiscErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "This counter shows the number of unclassified tranmission errors on a particular DS3 or E3 interface. This value may be cleared via the Engage User Interface." ::= { engageWANCommonDs3E3StatsEntry 2 } engageWANCommonDs3E3StatsTxQueueDepth OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS optional DESCRIPTION "This is the current number of data buffers awaiting transmission on this particular DS3 or E3 interface." ::= { engageWANCommonDs3E3StatsEntry 3 } engageWANCommonDs3E3StatsRxCrcErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "This counter displays the number of received CRC errors on this particular DS3 or E3 interface. This value may be cleared via the Engage User Interface." ::= { engageWANCommonDs3E3StatsEntry 4 } engageWANCommonDs3E3StatsRxOvErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "This counter displays the number of receiver overrun errors on this particular DS3 or E3 interface. This value may be cleared via the Engage User Interface." ::= { engageWANCommonDs3E3StatsEntry 5 } engageWANCommonDs3E3StatsRxFramingErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "This counter displays the number of receiver framing errors on this particular DS3 or E3 interface. This value may be cleared via the Engage User Interface." ::= { engageWANCommonDs3E3StatsEntry 6 } engageWANCommonDs3E3StatsRxMiscErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS optional DESCRIPTION "This counter displays the number of unclassified receiver errors on this particular DS3 or E3 interface. This value may be cleared via the Engage User Interface." ::= { engageWANCommonDs3E3StatsEntry 7 } engageWANCommonDs3E3StatsRxQueueDepth OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS optional DESCRIPTION "This is the current number of buffers in the receiver's FIFO of this particular DS3 or E3 interface." ::= { engageWANCommonDs3E3StatsEntry 8 } END